Contact Us

3310 S. Brunson Street
Oklahoma City, OK
73119 USA

Phone & Fax:
(405) 605-3765

Sales Questions:

Technical Questions:

Motorized Wheelbarrow Solid Axle 8 cubic feet Under Tub Honda GX35 Four Cycle Engine

Motorized Wheelbarrow Solid Axle 8 cubic feet Under Tub Honda GX35 Four Cycle Engine
Click to enlarge

More images

Click to enlarge
Sale Price: $799.00
Compared at: $1,188.60
You Save: $389.60
Product ID : 3198
Manufacturer: Staton-Inc
Weight: 150.00 lbs


Product is out of stock


The wheelbarrow is included with the engine and gearbox mounted under the tub to keep it clean.

Don't let the small Honda GX35 35.8cc 1.60 hp Four Cycle Engine fool you.

With the engine and gearbox under the tub it keeps the engine out of the way and you can start it from the rear where your throttle control and kill switch is mounted.

It very easy to change the air filter, add oil and gas.  It also has a very simple chain adjustment located by the front left wheel.

The #40 10 tooth sprocket on the gearbox is held on with two set screws and has a snap ring grove and snap ring to make sure the key does not come out.

Most units will have a #40 B 48 tooth 1" ID sprocket to drive the 1" Solid OD alxe and a #40 B 10 tooth 5/8" on the gearbox. 

The #40 48 tooth sprocket clears the ground by 3-7/8".  The bottom of the gas tank on the engine clears the ground by 7-1/2".

When it's mated to the Staton-Inc 18.75 to 1 reduction gearbox it will pull / move just about any thing you can get in the tub.

Be sure and watch the new youtube videos.

First look on the drive way.

No Operator, The wheelbarrow has 320 lbs in the tub. 

The best video would have been watching me run up that hill chasing the motorized wheelbarrow with the throttle wide open once it topped the hill.  It's pretty fast!

Thad + 320 lbs = 460 Lbs Going Up Hill

Keep in mind all these videos were taken the same day and the has only been ran doing these test. 

These engines gain 27% more power after the are broke in.

Both front wheels pull for extra traction and have a 6" wide foot print, the rear wheels have a 3.5" foot print.

Having 4 wheels and 19" of tread on the ground, makes going on soft ground, deep grass, sand or wet conditions super smooth.

No brake so you must use on flat ground and block the wheel and or chain up when not in use. 

You can add the brake option at an extra cost.

This unit comes with the raised handle bar kit and the X Frame Brace. 

3-25-15  I just had a Landscaper - concrete contractor that has two of these for 3-4 years and wanting a 3rd one.  He made a comment that this was the BEST investment he's made in 28 years of business!  Great for the back!.

Home owners, Landscapers, Contractors (this will fit in the front door for tear out), Roofers (to carry gravel and asphalt), Brick and Rock Layers, Concrete Contractors (use this for small jobs to get places where larger equipment can't), Plumbers, Tile layers (carry out & carry in), Great to carry fire wood, Build walk paths, Zoo's, Farm Use (you can do a million things with this on a farm), Great to clean up horse, cattle, pigs, goats and sheep Stall's and Barns.

I could go on and on about the things that can be done with this machine. But I bet you have just thought of a few more...

Note: A Human can put out .20 hp or 1/5 hp to .30 hp or 1/3 hp and only for a short period of time.

If you own a business, buy one of these and watch how much faster the work can be done and with a whole lot LESS work. This will pay for it's self several times.

One person can load this in a Truck. You can also drive it up ramps... you don't need to pull a trailer just to move the equipment.

9-25-14  Note: All the details below are subject to change.

The upper steering handles and throttle lever is 42" from the ground.
The end of the lower handles (used for dumping) are 28" from the ground.
The Front Drive axle is 1” OD and Drives TWO truf tires 6" wide, rated to carry a 620 pound load on each front tire. Max load for the tub is around 400 lbs.

Both wheels, and the sprocket is held in place by a ¼” key.

This small engine along with the Staton-Inc gear reduction box can put out 5 to 10 times more hp depending on the engine and it does not get tired!

Remember, this is a quiet, very easy to start, ( do not over pull the rope or pull it very hard ) very high quality Honda Four Cycle engine.

Plus you don't carry any of the load, all you do is steer it and hit the throttle.

Ground Speed: A centrifugal clutch allows the engine to keep running, and ground speed can be a snails pace or a very Brisk walk.

Both front wheels pull, so when you need to turn, just push to the side or lift up a little on the handle bars and the rear ribbed tires will slide on the across the ground and makes turns very easy.

It has a remote engine stop switch by the handle bar.

The load is very well balanced, so when you ready to dump, lift on the lower handles.

The drive system has CNC machined gear box that has Six high speed double sealed ball bearings and a 5/8" output shaft. 

The front 1" OD solid 1018 steel axle has been CNC machined with Heavy Duty 1" Ext. Snap Rings with a Tensile Strength (PSI)  150,000 to hold the two drive wheels in place, snap rings to hold the 1" Pillow Bloack Bearings in place and a CNC machined 1/4" keyway.  The Sprocket is held in place with two set screws and this also allows for the chain to be aligned.

We also CNC machined the Non Drive Axle with eight (8) heavy duty snap rings that hold the rear non drive wheels in place, snap rings side by side that hold the rear supports in place (and have removed the light sheet metal bracekt that came on the wheelbarrow) so it's easy to add gas, check the air filter and reach the starter rope.  The rear axle may be Hollow or solid.  The Heavy Wall tubing is 2 lbs 12 oz and the solid is 6 lbs 6 oz. 

We CNC machined brackets that hold and postition the gearbox in place so nothing moves side to side and makes the unit very rigid.

We have a easy to use chain adjustment to raise and lower the gearbox.

This model will fit through a 36" House door or gate.

The Engine and gearbox will be bolted together and installed on the wheelbarrow.  You will have to adjust the raised handle bars.

Do not throw or toss sharp or heavy objects into the tub or over load it. No warranty is on the tub.

Depending on your use you may want to cut and install a piece of plywood under the tub for extra support and more protection. 

Max weight around 400 lbs depending on the type of product you are moving. 

The engine and gearbox will move about any thing you can get in the tub and will run from Zero to at a FAST walking speed. 

Most people could not keep up with it running wide open. 


The Hour and Tach Meter is good to buy as it shows the number of hours the enigne has ran so you know when to do you oil changes and engine maintenance.

Hour & Tach Meter Flash Alert Service Alarm Flashes:   CLICK HERE To view the Hour & Tach Meter


This must be shipped by Truck Line and the web site will NOT charge the correct amount for shipping. 

Note: Due to the shipping weight the web site will not add the correct shipping cost.

PLEASE email us FIRST with your name, complete shipping address and let us know if this is a residential address.

We also need to know if you need a Lift Gate.

If you can pick it up at a Local Truck Line Dock or if your business address has a fork lift.

The average shipping cost range from $155.00 to $225.00.

The Dock Pick Up or shipping it to a business address with a Fork Lift will be cheaper.

Residential Fee is an can be an additional cost depending on your address.

If you need a Lift Gate (something that you cannot pick up out of the truck - trailer)
The Lift Gate fee is an additional cost around $35.00 extra.



Product Reviews

Login or Register to write the first review.

Products You May Like

Product ID : 3391
Weight: 150.00 lbs
Product ID : 3667
Weight: 150.00 lbs
Product ID : 3775
Weight: 150.00 lbs
Product ID : 3666
Weight: 150.00 lbs